Flat vulcanizing machine supporting vacuum pump Energy-saving and environmental protection V0100 air-cooled, rotary vane vacuum pump in terms of performance parameters. Vacuum degree and unit displacement are compatible with various aspects such as flat vulcanizing machine, but also to lead and improve the development of flat vulcanizing machine! one. use: This vacuum pump can be used to pump air and other dry, non-toxic, non-corrosive, non-explosive gases. It cannot be used to pump out gases containing particulate dust that will chemically react with the pump oil. (If a gas ballast device is attached, a certain amount of condensable gas can also be pumped out.) Withdrawing gas with a higher density than air will cause the mechanical load and heat load of the vacuum pump to increase. If it is not approved by Dalutong, please prohibit it. Use it like this. This vacuum pump is not allowed to be used in explosive atmospheres. If the vacuum pump is equipped with a float valve and a return pipe, continuous operation is available. (Be sure to observe the precautions during use. Refer to - Oil circulation and installation and commissioning in this manual.) This vacuum pump limit pressure has been verified. 2. The quality of all parts processing and assembly of this product meets the product drawings and related technical requirements, and complies with the relevant provisions of JB/T 5971-1992 and JB/T 6533-2005. Sealed parts conform to JB/T 109l-1991 and JB/T. The relevant provisions of 109l-1991 comply with the relevant provisions of GB/T 19956.1-2005 and GB/T 19956.2-2005 Volume Vacuum Pump Performance Measurement Method, and comply with GB/T 21271-2007 Vacuum Pump Noise Measurement and Standards. The relevant provisions of DIN45635. II. Structure 1, driven by a standard motor, built-in check valve to prevent backflow at shutdown. 2, compact structure, easy operation and maintenance, according to different application equipment special accessories. 3, air-cooled, oil circulation lubrication, built-in oil mist filter, exhaust clean. 4, low vibration, low noise, suitable for a wide range of industrial uses. 5. The vacuum pump is a rotary sliding vane vacuum pump with a simple design and a solid structure. Basic technical parameters of V0100 vacuum pump Pumping rate: 100 cubic meters/hour Ultimate pressure: 0.1 mbar Power supply: 380V Motor power: 3 KW Weight: about 75 KG Various accessories can be configured according to the application requirements, compact size, quiet operation, especially suitable for all types of machinery and equipment support. III. Working principle: In the cylinder body, the rotor 4 is mounted and secured through the eccentric hole of the end cap, and the close-to-left part 7 is almost in contact with the cylinder chamber wall. The rotor blades 3 are mounted in a plurality of rotor slots. When the rotor 4 starts to rotate, the centrifugal force causes the blades 3 to slide and slide along the inside of the cylinder, thereby separating the space between the cylinder and the rotor into several working chambers. When the working chamber is connected to the air inlet 1, gas is sucked. As the rotor 4 continues to rotate, the sucked gas is compressed and then discharged into the tank. A constant pressure difference causes the vacuum pump lubricant to enter the compression chamber. Lubricating oil is discharged into the tank together with the pumped gas. Under the action of gravity and the action of the oil filter net 6 and the exhaust filter (12), the oil and gas are separated, and the oil falls back to the bottom of the tank and enters the working chamber again (oil circulation ) Oil-free gas is vented to the atmosphere through the exhaust filter. In order to avoid inhalation of solid particles, the vacuum pump is fitted with an air intake filter (12) at the inlet. In order to prevent the blade from rotating backwards after turning off the power supply, the vacuum pump is equipped with a check valve 2 . (This valve cannot be used as a vacuum system check valve or shut-off valve, and after closing the vacuum pump, this valve cannot prevent oil from being drawn into the vacuum system.) If the vacuum pump is equipped with a ballast valve (11) (optional): A small amount of air passes through the gas cylinder The valve enters the vacuum pump chamber and is compressed along with the process gas, which prevents condensation of the condensable gas components in the process gas in the vacuum pump (refer to "Operational Notes"). The ballast valve is equipped with a paper filter element. (If the ballast valve is fitted With a ball valve, the ballast valve can be partially or fully closed by the ball valve.) Four. Applicable machinery: Vulcanizing machine / vulcanizing machine / Blister machine / Laminator / Rubber vulcanizing machine / Carved machine / Automated manipulator / Adsorption processing / Vacuum filming machine / Food packaging machine / Circuit board / Membrane switch / Mold vacuum / Vacuum machine suction cup / Engraving and milling machine / plate vulcanizing machine For more information, please consult China Vacuum Pump Trading Network. (/) Manual Hoists Manual Hoists,Manual Chain Hoist,Lever Hoist,Hand Chain Hoist Shandong Lite Electrical Co.,Ltd , http://www.chinacranegroup.com
Hand Chain Hoists are primarily for vertical lifting and uses the power of the worker for operation. The exception is the CM Hurricane 360 Hand Chain Hoist which incorporates a patented rotating hand chain guide that allows it to be used in a variety of ways. Lever Hoists are used effectively for pulling, lifting and positioning.Manual Hoists may also be purchased with integral trolleys and in styles that are ideal for low headroom applications.