New Hollow Hydraulic Feedback Heavy Oil Pump and Its Structural Optimization Design

Design and Calculation of a New Type of Hollow Hydraulic Feedback Heavy Oil Pump and Its Structural Optimization Design for Petroleum Machinery Cui Zhijian 12 Hu Hongping 2 Jiang Shunong 3 Chen Ziguang 3 Hu Yuantai 23(1. School of Petroleum Engineering, Xi’an Shiyou University2. Department of Mechanics, Huazhong University of Science and Technology 3 Mechanics and Sensing Technology of Central South University Institute) feedback, hollow sucker rods, and powerful open and close plungers and many other advantages. The structure optimization method that maximizes the actual pumping quantity is proposed. This method is used to optimize the matching design between the diameter of the feedback pump pump barrel and the working pump cylinder diameter of the heavy oil pump, so that the maximum pumping pump outer diameter can be fixed. The actual pumping volume is the largest. Theoretical analysis and numerical calculations show that the new type of hollow hydraulic force feedback heavy oil pump greatly improves the theoretical displacement compared with ordinary oil pump; for different pump pump cylinder diameters, the optimal feedback pump pump cylinder diameter is matched to make single stroke The actual pumping volume reaches the maximum.

The feedback pump cylinder diameter and working pump cylinder diameter have been optimized. Due to the high viscosity of heavy oil and high flow resistance, when the heavy oil is pumped by a conventional pump, the difficulty of the sucker rod column and the eccentric wear of the rod tube often occur. It is difficult for the heavy oil to enter the pump, the fullness coefficient of the pump is low, and the valve ball is closed and lags behind, resulting in a low pump efficiency and affecting the production efficiency of the oil well. A new type of hollow hydraulic force feedback heavy oil pump (hereinafter referred to as the new heavy oil pump) was designed to solve the problems often encountered in the extraction of heavy oil. The structural and hydraulic feedback working principle structure of the new heavy oil pump structure is shown. The hollow sucker rod runs through the entire oil extraction pipeline, the heating cable is in the hollow sucker rod, and the hollow sucker rod forms a heating loop.

2 How the hydraulic feedback works The space between the feedback plunger and the working plunger is called the working chamber.

On the upstroke, the hollow sucker rod drives the feedback plunger and the working plunger to move upward. The distance between the two plungers does not change. Since the diameter of the feedback plunger is smaller than the working plunger, the working chamber volume decreases and the pressure increases. Large, the moving valve is closed, and the feedback valve and the feedback plunger are forcibly opened. The liquid in the pump is discharged into the oil pipe through the feedback valve until it reaches the ground.

On the down stroke, due to the frictional force, the downward movement of the feedback plunger due to gravity lags behind the hollow sucker rod, and part of the oil flow can still enter the upper part of the pump through the feedback plunger. Until the hollow sucker rod drives the feedback valve downward, the feedback valve and the feedback plunger are forcibly closed. The thick oil above the feedback piston forms the liquid column pressure and acts on the feedback plunger to generate a downward pulling force on the sucker rod ( That is, hydraulic feedback), which solves the problem of the difficulty of the sucker rod downwards and the eccentric wear of the rod tube. At the same time, the working chamber volume increases, and due to the larger diameter of the working plunger, the pressure reduction is relatively large. Under the action of sunken pressure, the traveling valve opens and the oil flow enters the working chamber smoothly, solving the difficult problem of pumping heavy oil.

It should be noted that the feedback valve and the working valve in the working pump cylinder have different forms of opening and closing. The former is forced to open and close between the hollow sucker rod and the feedback plunger.

The new heavy oil pump combines the advantages of a powerful open-close plunger, a hollow sucker rod and hydraulic feedback suitable for heavy oil production.

The feedback valve of the hollow suction pump is mechanically forced to open and close11, which can prevent air lock and increase the flow area, thereby reducing the resistance of the liquid passing through and improving the pump efficiency.

When the working plunger goes up, due to the difference between the diameters of the feedback plunger and the working plunger, the pressure in the working chamber is large, which is beneficial to the upward movement of crude oil, and the pumping efficiency of the working chamber is increased. 121. The pressure of the liquid column in the tubing during the downstroke On the feedback plunger, a downward pulling force is generated on the hollow sucker rod, so that the sucker rod string is in a tensioned state during the downward process, thereby solving the difficult problem of sucker rod string down in the heavy oil well and effectively preventing The sucker rod bends to reduce the stroke loss and eccentric wear of the rod tube and improve the pumping efficiency. 12. At the same time, due to the difference between the feedback plunger and the working plunger diameter, the difference between the pressure in the working chamber and the pump sinking pressure increases, which overcomes the heavy oil. Difficulties in pumping.

The use of hollow rod over-pump (or over-pump) electric heat recovery technology enables the whole process of oil production from the pump, pump, and pump to be conducive to the recovery of heavy oil and high-condensation oil. 131. No action string, By injecting the heat carrier and the viscosity reducer under the pump through the hollow sucker rod, the viscosity of the crude oil is reduced. The hollow sucker rod can also perform downhole testing and inject steam into the thick oil layer to implement a steam stimulation process 111. Performance analysis and structural optimization The equivalent diameter of the new heavy oil pump is equal to 38.10 mm, the substituted elastic modulus, and the lower pump depth , D equivalent pump diameter, m. The impact of inertial load on the piston stroke into i so in the case of the same stroke and stroke times, the ratio of the theoretical displacement of the HLB type pump and the new heavy oil pump is the equivalent pump of the HLB type pump The diameter is 71994-201 ChmaAcSei The working plunger stroke is considered after static and dynamic loads. The pump efficiency under load is the degree of influence of the gas on the pump efficiency. It is expressed by the fullness factor 卩, R is the ratio of the gas to oil in the pump, and k is the remainder. Gap ratio, so the pump efficiency under gas n is such as neglecting the effect of leakage, the actual pumping volume for a single trip is 700m, and the number of strokes is n=10mn-1. When the stroke times and the rod stroke are the same, only the calculation of the pump is required. The single stroke actual pumping volume. From the above derivation, we can draw the following conclusion: In the case of a fixed working pump cylinder diameter of 105mm, under different pump air-oil ratio, the actual oil pumping capacity of a single trip with the feedback pump cylinder diameter curve can be seen in different working pump cylinder diameter The actual pumping amount of the stroke is the curve of the diameter of the pump cylinder with the diameter of the pump cylinder of the feedback pump, and the actual pumping amount of one stroke is the curve of the pump cylinder diameter of the feedback pump. It can be seen from the figure that for different working pump pump barrel diameters, different feedback pump pump barrel diameters should be selected to match the optimal value so that the single stroke actual pumping quantity reaches the maximum.

From equation (5), it can be seen that the smaller the diameter of the pump cylinder of the feedback pump is, the larger P is, and the larger the theoretical oil production per stroke is. At the same time, it is also known that the larger the stroke loss, the smaller the efficiency of the load pump, and the smaller the actual stroke of the working plunger is, the smaller the actual meter oil amount of this single stroke is. It can also be seen that there is an optimal feedback pump cylinder diameter that maximizes single stroke pumping. In the figure, the inner diameter of the inner diameter of the feedback pump cylinder is D1=50mm, the maximum single-stroke pumping volume is 2.26×10-2m3, and the greater the gas-oil ratio R in the pump, the smaller the D1 should be. Therefore, when the pump cylinder diameter of the working pump is the same, the diameter of the pump cylinder of the feedback pump can be optimized to maximize the pumping volume.

Concluding remarks It is an effective method to extract heavy oil by adopting a mechanical forced opening and closing valve, hydraulic feedback, hollow sucker rod, current or steam heating viscosity reduction and viscosity reduction agent viscosity reduction. At the same radial size, the new heavy oil pump greatly increases the theoretical displacement compared to ordinary oil pumps. Through structural optimization, the diameter of the feedback pump cylinder can be matched with the pump cylinder diameter, so that the maximum pumping volume can be achieved.

Turning Parts:

Turning the workpiece in a lathe using the method of cutting tool rotation processing workpiece. Turning processing cutting is mainly composed of workpiece and not provide tools. Turning is the most basic, the most common method of cutting, occupies a very important position in the production. Turning for processing rotary surface, a large part of workpiece with rotating surface turning method of processing can be used, such as the external cylindrical surface, inside and outside the cone face, face, groove, screw and rotary forming surface, the tool is mainly used tools. Turning precision is generally it11-it7, some can reach IT6, surface roughness Ra 12.5-08um. can be achieved by Turning Parts, we call turning parts, there are many kinds of turning parts, most famous is via hard turning to maintain the thermal stability of the parts.

Category:

Based on different facilities(CNC facility) to do the turning process,CNC turning parts included Lathing Parts,milling parts,Grinding Parts;

Basically,we can realise it on different raw material,like copper alloy,steel,and aluminium alloy.

Concerned Factors:

(1) The biggest problem is to use or without cooling liquid. For interrupted cutting parts such as gears, the best use of "dry turning", otherwise the thermal shock feed and withdrawal knife is likely to cause the blade to rupture. As for the continuous cutting knife head, high temperature produced in dry turning process to toughening (softening) the pre cutting area, thereby reducing the hardness of the material to make it easy to cut. This phenomenon shows that the stem cutting speed increase is good. At the same time, no coolant cutting method has obvious cost advantages. (2) Layer whitening whitening scald layer (heat affected zone) "may be a dislike to appear in hard turning and grinding operation, namely in the material surface to form a layer of invisible to the naked eye is very thin (typically 1 m) crust. The formation of albino layer in the hard turning process, usually because of blade Passivation causes too much heat to the inner parts. Often whitening on bearing steel form, and it is very harmful to the bearing ring like need to withstand high contact pressure parts, with the passage of time, the albino layer may stripped and lead to bearing failure.

(3) Machine:stiffness determines precision hard turning. Nearly 15 ~ 20 years of manufacturing machines in the almost all have good rigidity, enough to withstand hard turning. In many cases, the overall condition of the machine is largely over the use of life is more important, the general maintenance The opening of the bed can also be used for hard turning. In order to increase the rigidity and damping characteristics for hard turning machine, hatey characteristics of many advanced machine tool for the machining center, including polymer composites reinforced with a spring clip (the spindle support near the workpiece) is directly matched with the spindle and hydrostatic guideway system. The maximum rigidity means a tool to reduce vacant, and extending parts out, and cancel the adjustable gap plate and gasket, its goal is to keep all parts as close as possible to the turret.

(4) Process:because of the heat generated by hard turning most chips away, before and after the processing of chip inspection You can find the whole process is coordinated. Continuous cutting, the chip should be blazing orange, and like a ribbon like flowing out. If the chip after cooling by hand pressure fracture, shows that cutting heat is normal.

(5) Blade:cubic boron nitride (CBN) inserts the price is expensive, but the most suitable for the hard cutting blade CBN.Cbn blade can keep unchanged in the positioning of intermittent cutting process, to provide a safe tool wear rate in continuous cutting process. When using the hard turning process reasonable, except in the control of CBN blade diameter tolerance is not better than grinding, other properties are second to none.

Turning Parts

Turning Parts,Lathing Parts,Milling Parts,Grinding Parts

VESTA Motoring Ltd , https://www.vesta-industry.com