Recently, the large-scale automobile recall incident triggered by the failure of Japan's Takada airbags once again pushed the " airbag " to the cusp. In China, complaints about car airbags also have a long history. Due to the lack of uniform standards, since 2009, there have been countless incidents involving airbags, accident disputes and difficult consumer rights protection. In 2011, China's national standard for automotive airbags was formally established, but it has not yet been introduced. In April 2013, the Airbag Standard Research Working Group meeting was held at Shanghai Dongfang Jiule Automobile Airbag Co., Ltd. The meeting discussed and revised the national mandatory standards for “Miscellaneous action test methods and requirements for automotive airbag systemsâ€. Sun Zhendong, a senior engineer of the Automotive Standards Institute of China Automotive Technology and Research Center, who attended the conference, told the reporter: “The national standard for airbags has been basically formulated and completed. Now we mainly do some verification work. Our goal is to announce at the end of 2013.†The road to standards is long In fact, China has been studying the national standard for airbags. In April 2006, the State issued the recommended national standard for airbags, "Airbag Components for Road Vehicles" (GB/T 19949), which is divided into three parts, the first part of the terminology, the second part of the airbag module test, the third part Gas generator assembly test. This standard specifies the test methods, environmental test procedures and requirements for the airbag components of road vehicles and the terms used therein. However, it is only a standard for an airbag module and cannot be used as an evaluation standard for an airbag integrated system. In October 2009, the associations of Liaoning, Sichuan, Jiangsu and other provinces and cities lost their standards, resulting in the inability to determine the quality of airbags and the difficulty of protecting consumers' rights. This was addressed to the Ministry of Industry and Information Technology, AQSIQ, and the National Standardization Administration. Submission of the "Proposal on the Promulgation of National Standards for Automotive Airbags as soon as possible". Sun Shidong, a passive safety engineer from Shanghai Dongfang Jiule Automobile Airbag Co., Ltd., told reporters: “There was no standard for the accidental explosion of airbags. It will certainly need such standards afterwards. After standards have been established, when airbags are inadvertently inflated, they can be compared with national standards. Check whether the airbag is qualified to avoid unnecessary disputes. Hao Xiaosong of BYD Auto Sales Co., Ltd. believes that the introduction of standards can improve security and enable users to receive benefits and security. In 2009, the National Automotive Standardization Technical Committee initiated the research project on national standards for automotive airbags and submitted an application for the standard to the National Standardization Committee. In May 2011, the Automotive Airbag Standards Research Working Group was established and consists of 21 experts from 17 organizations. Airbag national standard formulation work officially started. Multinational corporations set resistance From 2006 to 2013, the eight-year war still came to an end. Why does the airbag national standard always “do not call outâ€? What problems exist in the formulation process that cannot be overcome? An expert involved in the development of airbag standards told reporters that the formulation of airbag national standards is mainly facing two obstacles: First, technology, and first, multinational companies. According to reports, although there are some standards related to airbags in foreign countries, there is no standard for the misuse of airbags. China has formulated standards for the misuse of airbags. Foreign and joint-venture car companies believe that they are setting trade barriers and have been blocking the introduction of airbags. Liu Yuguang, deputy chief engineer of the National Automobile Quality Supervision and Inspection Center Automobile Testing Research Institute, said: “More than one rule is a constraint for car companies, especially foreign companies, they will worry about unnecessary situations, and one more technical specification may be possible. Become a trade barrier." Some experts in the industry are also playing a counter part. For example, Zhu Xixi, a professor at Tongji University’s School of Automotive Studies, was skeptical of formulating airbag national standards when interviewed by reporters. He said: "What is the standard used? Is there a standard that can solve all kinds of disputes caused by the accidental explosion of airbags? Can a few simple standards solve the complex problems of airbags? Is it standard? Are cars that meet the standards not called defects?" According to the experts involved in the formulation of standards, “In order to resolve the resistance of multinational corporations and other parties, we invited the transnational corporations to participate in the process of standard setting and coordinate with the parties.†Technical problems are being solved Returning to the technical level, China's development of standards for the misuse of airbags is entirely based on China's actual road conditions and model applications, and it is technically difficult. Liu Yuguang stated: “When an airbag is detonated and when it should not be detonated, technically speaking, ordinary cars are not the same as SUVs and MPVs. It is necessary to bring these two together to form a unified standard. Technically, Difficulty, of course, is not totally unsolvable." Sun Shidong also believes: "The test conditions for airbags are very harsh, such as the roadbed. Its height is regulated, and therefore the technical requirements are very high." Although the development of airbags mishandling national standards was a difficult process, reporters learned that everyone has a positive attitude towards the introduction of the standard. Sun Zhendong said that the current standard has basically been completed and the follow-up work is mainly to carry out technical verification of the standard and obtain the approval of domestic and foreign companies, and strive to be introduced at the end of 2013. This station is suitable for industrial, civil construction, roads, railways, bridges, electric power, water conservancy, port terminals, airports and other projects. It can be used as a mixing equipment for commercial concrete production, and combined various forms different specifications concrete mixing plant according to the needs of different users. Automatic Batching Machines,Weigh Batching Machine,Material Batching Machine,Aggregate Concrete Batching Machine Shandong Zeyu Heavy Industry Science and Technology Co.,Ltd. , https://www.sdjsseriesconcretemixer.com