We are Plastic 3D printing services company which offer almost all kinds of plastic 3d printing services.
3D Printing Service,metal 3d printing,sla sls printing Ningbo Rongna Technology Co.,Ltd , https://www.prototyping-machining.comDesiccant Compressor Air Dryer Heatless 5% Purge PDP -40f 
Features1. Less than 5% purge air without auxiliary equipment, 012KW power consumption
2. Pressure and inlet temperature is digital readout on screen; purge air gauge allows manually control regeneration air according to the wanted pressure dew point
3. Small desiccant chambers' group, each chamber unit is independent and detachable
4. Replace with factory filled desiccant chamber, ease of maintenance and constant pressure dew point -40ºC (-40ºF) is ensured
5. The lowest operation cost, user could recoup dryer investment in three years by saving huge air and electricity
6. 1/3 size to traditional dryer
7. The shortest downtime
8. Using Molecular sieve as desiccant
How it works
Drying cycleThe process air enters the dryer through the inlet and is directed into the on-line drying chamber via the inlet valves and lower manifold.
The air is evenly distributed through the drying units and passes over the desiccant material, reducing the water vapour content.
The dried process air then combines in the upper manifold and exits the dryer via the outlet check valves
Column changeoverBefore the on-line (drying) and off-line (regenerating) columns change over, the dryer exhaust valve, is closed, allowing the purge air to re-pressurise the off-line columns. This ensures a consistent system pressure and dewpoint when the drying chambers change over.
Regeneration cycleAt the start of the regeneration cycle, the exhaust valve of the dryer is closed and the off-line chamber is at full line pressure. The air in the off-line chamber has a dewpoint equal to the air leaving the dryer.
The exhaust valve is then opened and the dry air within the chamber expands rapidly as it leaves the dryer via the exhaust silencer, forcing water to be removed from the desiccant material.
Once the off-line chamber has de-pressurised, a continuous bleed of dried process air is directed into the off-line upper manifold. This air is known as purge air.
With the exhaust valve open, the purge air expands from line pressure to atmospheric pressure and flows downwards through the columns, over the off-line desiccant material.
As the purge air at line pressure contains a fixed amount of water vapour, allowing it to expand means the purge air becomes even drier, increasing its capacity to remove water from the saturated desiccant bed.
Details of advantagesInnovative structure with patents, adopts small desiccant chamber unit
Â
1. Air flow equally and evenly pass through each desiccant chamber
2. Avoid channeling effect which more likely happens in traditional desiccant dryer
3. Small chamber allow no pressure vessel annul inspection
4. Molecular sieve capability is much better than Alumina and silicon desiccant in traditional dryer
5. Easy to maintain and replace factory filled desiccant chamber unit, ensure good performance as beginning
6. PLC controller, Full function touch panel control
Product details
Specification data
BTGMXW-B Series
Heatless
Model
Pipe Size (inch)
Flow Range(m³/min)
Dimension(mm)
Weight(kg)
@5~6bar
@6~7bar
@7~10bar
L
W
H
BTGMXW015-B
G1
1.1
1.3
1.5
380
240
828
78
BTGMXW026-B
G1
1.9
2.3
2.6
380
240
978
87
BTGMXW038-B
G1
2.7
3.3
3.8
486
240
978
106
BTGMXW065-B
G2
4.8
5.8
6.5
486
240
1628
159
BTGMXW085-B
G2
6
7.4
8.5
595
240
1628
192
BTGMXW106-B
G2
7.4
9.1
10.6
703
240
1628
226
BTGMXW146-B
G2
9.8
12
14.6
920
240
1628
293
BTGMXW165-B
G2
11.6
14.2
16.5
1029
240
1628
327
BTGMXW206-B
G3
14.6
17.8
20.6
1250
240
1628
380
BTGMXW248-B
G3
16.7
20.5
24.8
829
480
1628
510
BTGMXW295-B
G3
21.5
26.3
29.5
938
480
1628
574
BTGMXW336-B
G3
24.1
29.5
33.6
1047
480
1628
638
BTGMXW385-B
G3
26.8
32.8
38.5
1156
480
1628
702
BTGMXW425-B
G3
29.7
36.4
42.5
1265
480
1628
767
BTGMXW465-B
G4
32.7
40.1
46.5
1374
480
1628
831
Installation
About Biteman technologyBiteman technology, the leading supplier and manufacturer of high efficiency desiccant air dryer and filter in China, with the advantages in low consistence PDP -40ºF, high efficiency 5% purge air, and easy to maintain, has widely applied for GM/P&G/Gree/BYD all over the world.
Â
Contact us today to learn more. www.bitemantech.com
Â
Rapid prototyping 3D printing services such as high quality fdm and GDM printing, low-volume production, desktop manufacturing, desktop direct printing, cookie sheet production, die cutting, lamination, desktop publishing, plating, Zebra printing, UV coating, hard coatings, gloss coating, gloss engraving, membrane carving, fiberglass coating, acrylic ink, nylon coating, melamine coating, CMYK printing, foil stamping.We can produce plastic objects out of metal or plastic and without disturbing the original design. Customizable
Desiccant Compressor Air Dryer Heatless 5% Purge PDP -40f
Model NO.: BTGMXW015-B
Operational Method: Continuous
Display: PLC and Touch Panel
Flow Range: 1.5m3/Min, 50cfm
Pressure Dew Point: -40f
Heat or Heatless: Heatless
Purge Air: 5%
Standard Working Pressure: 7 Bar-10 Bar
Inlet Temperature: Below 35 Centigrade Degree
Modular Units Desiccant Chamber: Replaceable Factory Filled Desiccant Chamber
Pressure Drop: Less Than 0.012MP
Noise: Less Than 75dB
Trademark: Biteman
Transport Package: Plywood Case and Carton
Specification: 380*240*828mm
Origin: China
Â