70X120mm Radial Tire Repair Patch

General Info.

 

 Part No.: RP-T701

Specification: 70X120mm, 1 ply

Packing: 10pcs/box, 24box/CTN

 

Selling Points

 

1. Each reinforcing ply individually end-wrapped to defect tire flexing stresses in a unique manner.

 

2. Tie-gum construction eliminates the potential for delamination common in competitive products.

 

3. Designed to vulcanize chemically or in low temperature systems

 

4. Gray vulcanizing gum, blue poly backing

 

Quality Guaranteed

 

Excellent quality, similar to Rema Tip Top and Tech; Samples can be sent for customer's testing and evaluation.

 

Description

 

HOPSON offers a variety of radial-ply repair units to meet the diverse demands of today's passenger, truck, and OTR tire applications. HOPSON radial repair patches are thick, rubber-reinforced patches which allow placement on the tyre in any direction. A special compounding and design allow the repair unit to flex and resist heat, assuring a permanent repair.

INSTRUCTIONS

• Inspect tyre for repairability using tyre manufacturer of HOPSON LAB guideline. If repairable, mark injury with crayon and carefully remove injuring object.
• Probe injury to determine exact size and direction, removing all deris.
• Select the appropriate repair patch for injury and type of tire. Apply prebuff cleaner to repair area and use rubber scraper to remove dirt and mold lubricants. Using carbide cutter, drill injury channel 3 times from inside then 3 times fron outside, making sure all damaged and rusted cables have been removed and only good rubber remains.
• Cement the injury channel with Chemical Vulcanizing Cement and install the appropriate vulcanizing insert. Trim flush with the tire innerliner. Mechanically buff outlined repair area to a velvet-like texture. Remove buffing dust with a clean brush or vacuum. Apply Chemical Vulcanizing Cement to buffed area, working into rubber and ALLOW TO DRY THOROUGHLY.
• Remove backing and center repair patch over injury and thoroughly stitch down from center out to remove trapped air.
• Finish repair by applying Inner Liner Sealer around edge of repair patch and to overbuff area.

 Don't miss the opportunity to check our full range of tire repair products. 

 

HOPSON TYRE REPAIR will always surprise you! 

General Info.

 

 Part No.: RP-T701

Specification: 70X120mm, 1 ply

Packing: 10pcs/box, 24box/CTN

 

Selling Points

 

1. Each reinforcing ply individually end-wrapped to defect tire flexing stresses in a unique manner.

 

2. Tie-gum construction eliminates the potential for delamination common in competitive products.

 

3. Designed to vulcanize chemically or in low temperature systems

 

4. Gray vulcanizing gum, blue poly backing

 

Quality Guaranteed

 

Excellent quality, similar to Rema Tip Top and Tech; Samples can be sent for customer's testing and evaluation.

 

Description

 

HOPSON offers a variety of radial-ply repair units to meet the diverse demands of today's passenger, truck, and OTR tire applications. HOPSON radial repair patches are thick, rubber-reinforced patches which allow placement on the tyre in any direction. A special compounding and design allow the repair unit to flex and resist heat, assuring a permanent repair.

INSTRUCTIONS

• Inspect tyre for repairability using tyre manufacturer of HOPSON LAB guideline. If repairable, mark injury with crayon and carefully remove injuring object.
• Probe injury to determine exact size and direction, removing all deris.
• Select the appropriate repair patch for injury and type of tire. Apply prebuff cleaner to repair area and use rubber scraper to remove dirt and mold lubricants. Using carbide cutter, drill injury channel 3 times from inside then 3 times fron outside, making sure all damaged and rusted cables have been removed and only good rubber remains.
• Cement the injury channel with Chemical Vulcanizing Cement and install the appropriate vulcanizing insert. Trim flush with the tire innerliner. Mechanically buff outlined repair area to a velvet-like texture. Remove buffing dust with a clean brush or vacuum. Apply Chemical Vulcanizing Cement to buffed area, working into rubber and ALLOW TO DRY THOROUGHLY.
• Remove backing and center repair patch over injury and thoroughly stitch down from center out to remove trapped air.
• Finish repair by applying Inner Liner Sealer around edge of repair patch and to overbuff area.

 Don't miss the opportunity to check our full range of tire repair products. 

 

HOPSON TYRE REPAIR will always surprise you! 

Engine Oil Filler Cap

An oil filler cap is fitted to the oil filler pipe to cover the hole in which the engine oil is poured. It retains the Oil Pan in the oil and prevents it from overflowing or leaking into the engine compartment. Oil-filled caps can be made out of plastic, aluminum, steel, rubber, and metal. Although the position of an oil filling cap varies depending on the makeup and model of the car, it is usually easy to locate. It is usually located on the top of the engine, especially on the valve cover, which has an oil symbol on its surface. Other oil filling caps have the word "engine oil" on them.

Audi Engine Oil Filler Cap,Engine Oil Filler Cap Bmw,Bmw Engine Oil Filler Cap,Oil Filler Cap For Bmw

WENZHOU PETURS AUTO PARTS CO.,LTD , https://www.cnpeturs.com