An electric Spray Bottle is an advanced version of a traditional spray bottle, powered by electricity or batteries. It is designed to dispense liquids such as water, cleaning solutions, or pesticides in a fine mist. The main advantage of an electric spray bottle over a manual one is that it requires less effort to use. It can continuously spray with just a press of a button, making it easier for tasks like watering plants, cleaning, or disinfecting. Some electric spray bottles also allow you to adjust the intensity of the mist according to your needs.Plastic Spray Bottles Mist Spray Bottle,Spray Mister,Mist Bottle,Plastic Spray Mist Bottles,diffusers for essential oils,aromatech diffuser,home fragrance diffuser Kunshan Muchun Electric Co., LTD , https://www.muchunmanufacture.com
Rubber Internal Mixer (X(S)N-75L) , Internal Mixer
Brief Introduction:
1.    Mixing Chamber
The mixing chamber is mainly made by alloy steel with harden treatment. The surface of internal chamber is with anti-wear alloy metal built up welding and plated with durable and anti-corrosion hard chrome.
2.    Regular Note Pump
Timing injection pump to the sealing system on a regular injection of hydraulic oil, lubrication sealing effect.
3.    Thermal Resistance (or thermal couple)
There is a plug-in thermal resistance or thermal couple in middle section of the bottom of the chamber to be connected to electrical system to inspect and control the mixing temperature.
4.    Rotors
It is designed to the hollow blades of banbury type. The hollows are connected with axial hole of rotor shaft used as cooling or heating passage. The top edges and the side faces of blades are surface welded with hard alloy, then plated with hard chrome and polished.
5.    Cooling/heating System
A common piping system is adopted for either cooling or heating material in mixing operation. Through the system cooling water or steam is fed in three ways to the cavities of the rotors blades, - the jackets of the mixing chamber and the top ram.
6.    Tilting Mechanism
It consists of a rotor with brake, cycloidal gear reducer, TP type worm and worm gear, etc. It is able to actuate the mixing chamber tilting by 140° around the front rotors.
7.    Dust Stop Device
At the joint between the top of mixing chamber and the cantilevered arm of the machine frame, the dust sealing assembled with curved slotted partings are used for obtaining an excellent and reliable sealing purpose. The end face of the rotor is sealed by end contact sealing with non oil-lubrication and it seals well and is wear-resistance and durable.
8.    The transmission system
The transmission system adopts harden-gear speed reducer with a compacted structure for lower noise, longer product life and increased safety factor.
9.    Pneumatic control system
Pneumatic control system is controlled by PLC order. A bi-directional air cylinder makes the ram up or down. In case of the over load occurs when mixing chamber, the top ram can be raised automatically or manually if necessary, so as to protect motor from overloading.
10.  Electrical Control System
Imported PLC device and electric control components which are all imported products or imported technology products are adopted in the electric control system to raise control reliability.
Technical Parameter
Models
X(S)N-3L
X(S)N-5L
X(S)N-10L
X(S)N-20L
X(S)N-35L
X(S)N-55L
X(S)N-75L
X(S)N-110L
X(S)N-150L
X(S)N-200
Total Volume of Mixing Chamber (L)
  8
15
25
  45
   75
125
    180
250
325
440
Working Volume of Mixing Chamber (L)
 3
5
10
   20
   35
55
     75
110
150
200
Rotating Speed of Front Rotor (r/min)
 32
32
32
   32
   32
32
    32
30
30
30
Rotating speed of Rear Rotor (r/min)
 24.5
23.5
25
   26
   26
26
     26
24.5
24.5
25.4
Driving Motor Power (KW)
 5.5
11
18.5
   37
   55
75
     110
185
220
280
Tilting Motor Power (KW)
 0.55
1.1
1.1
  1.5
   2.2
2.2
     4
5.5
11
11
Tilting Angle
 140°
140°
140°
   140°
    140°
140°
       140°
140°
135°
135°
Pressure of Compressed Air (Mpa)
 0.5-0.8
0.6-0.8
0.5-0.8
  0.6-0.8
   0.6-0.8
0.6-0.8
       0.6-0.8
0.6-0.8
0.6-0.8
0.6-0.8
Pressure of Cooling Water (Mpa)
 0.2-0.4
0.2-0.4
0.2-0.4
   0.2-0.4
   0.3-0.4
0.3-0.4
        0.3-0.4
0.3-0.4
0.3-0.4
0.3-0.4
Consumption of Compressed Air (m³/min)
 ≥0.3
≥0.5
≥0.5
   ≥0.7
  ≥0.9
≥1.0
      ≥1.2
≥1.5
≥2.0
≥4.0
Pressure of Heating Steam    (Mpa)
 0.5-0.8
0.5-0.8
0.5-0.8
    0.5-0.8
   0.5-0.8
0.5-0.8
       0.5-0.8
0.5-0.8
0.5-0.8
0.5-0.8
Size (L×W×H) (mm)
 1660×960×1750
1850×1200×2580
 2300×1360×2120
 2500×1750×2450
 3150×2020×2960
 3370×1950×3020
 3770×2570×3160
 4060×2750×3590
4250X2750X4106
4250X3400X4215
Gross Weight
(tons)2
2.1
3.3
4
6.3
7.1
9.5
14.9
19.5
22.5